Its snowing outside, white stuff from above.
I will spend time in the workshop, rather then being out riding my bikes.
Not so back in the days, snow just meant get them skies attached and put a snow chain on the back wheel!
fredag 26. desember 2014
tirsdag 23. desember 2014
What is the length of a rope?
What is the length of a rope?
A old saying which is commonly used when trying to describe a measurement which is uncertain.
Then it is far more easy to determine; "What is the length of a Harley cutdown front mudguard"?
The recipe is as follows:
Take one HD rear mudguard, preferably an original. Cut one piece to fit what you find is the correct length for the rear mudguard, what is left is what you have for the front.
Quite easy?
Having straightened umpteen bends and dents, it now in a brief glimpse looks like a mudguard again.
Next task is to start welding the total of 24 holes someone through time have found necessary to drill in a mudguard length of 16", hey ho work for tomorrow!
Tomorrow is the day, Merry Christmas to all!
A old saying which is commonly used when trying to describe a measurement which is uncertain.
Then it is far more easy to determine; "What is the length of a Harley cutdown front mudguard"?
The recipe is as follows:
Take one HD rear mudguard, preferably an original. Cut one piece to fit what you find is the correct length for the rear mudguard, what is left is what you have for the front.
Quite easy?
Having straightened umpteen bends and dents, it now in a brief glimpse looks like a mudguard again.
Next task is to start welding the total of 24 holes someone through time have found necessary to drill in a mudguard length of 16", hey ho work for tomorrow!
Tomorrow is the day, Merry Christmas to all!
lørdag 20. desember 2014
Getting ready for Christmas
Have my grandchildren here to stay over, great fun. After they had been kicked to bed I had to sneak down in the workshop and do just a little. Narrowing the width of my Cutdown foot boards is just that little enough :-)
When I was there (in the workshop) anyway, I couldn`t resist in making a mock-up with them great Allstate Dirtman tires I received from my internet friend "Taxi" in Japan yesterday, looks so good, I cant wait to see this baby rolling.
When I was there (in the workshop) anyway, I couldn`t resist in making a mock-up with them great Allstate Dirtman tires I received from my internet friend "Taxi" in Japan yesterday, looks so good, I cant wait to see this baby rolling.
Etiketter:
Cutdown project,
Small talk
fredag 19. desember 2014
Reading Standard Motorcycles
Another Reading Standard photo from the early Norwegian Motorcycle scene. The brothers Knut & Peder Espedal on brand new RS`s, bought the same day, hence the consecutive registration numbers.
What beauties those early RS`s was, loads of nickle plating and gold pin striping.
What beauties those early RS`s was, loads of nickle plating and gold pin striping.
lørdag 13. desember 2014
fredag 12. desember 2014
Ready for take off!
Start no. 35 Andreas M. Bjørnestad and Nic. Lunde ready to take off on their Harley Davidson model W`s.
Check out more on Nic. Lunde`s motorcycle racing by using the link above.
Check out more on Nic. Lunde`s motorcycle racing by using the link above.
Puncture!
This is a great photo showing Macke Nicolaysen (he was a
Norwegian Reading Standard super user for several years) having a puncture on
both wheels.
An interesting detail is the artillery wheel caps, commonly used
here in the first years after the WWI on the US made bikes.
Around South Norway in 1921, back then Scandinavias longest endurance run.
Have posted several photos from Yesterdaze on various Facebook sites lately, seems like facebook and Instagram is where "everyone" stays these days. But I will continue to stay true to the AMcN blog and will repost them here for you, where they should have been presented in the first place.
I have to pull myself together!
This first post shows a couple of great photos from an endurance run around South Norway held by NMK back in 1921.
This was the longest endurance run ever held by NMK and the press focused a lot on the event. I have a bunch of great photos from this weekend, and got to make an article from this event eventually, when there is time.
For now, photos, will add the words to later.
I have to pull myself together!
This first post shows a couple of great photos from an endurance run around South Norway held by NMK back in 1921.
This was the longest endurance run ever held by NMK and the press focused a lot on the event. I have a bunch of great photos from this weekend, and got to make an article from this event eventually, when there is time.
For now, photos, will add the words to later.
I have posted pics from this location before in "Pics from yesterdaze", go check it out
mandag 8. desember 2014
Modifications from way back when.
Working with old molested and abused motorcycle parts sometimes make me think, why?
Why did someone cut apart, bend or weld a part to give it the shape it have when looking at it today?
There have had to be a reason for those modifications that I find, who cause me such a lot of work.
Like with the gear change lever I found among my spares that I am using for my cutdown project.
Why on earth would someone grind the lever on each side where it is run in the shifter gate? For me, the only apparent result achieved was making the lever so weak it would easily break when used, and yes I found it when still mounted on an original HD tank.
I bet I used more time with the repair, than what the guy who once modified did.
As found, someone played with a grinder.
Chopped.
One side done, one more to do still.
Why did someone cut apart, bend or weld a part to give it the shape it have when looking at it today?
There have had to be a reason for those modifications that I find, who cause me such a lot of work.
Like with the gear change lever I found among my spares that I am using for my cutdown project.
Why on earth would someone grind the lever on each side where it is run in the shifter gate? For me, the only apparent result achieved was making the lever so weak it would easily break when used, and yes I found it when still mounted on an original HD tank.
I bet I used more time with the repair, than what the guy who once modified did.
As found, someone played with a grinder.
Chopped.
One side done, one more to do still.
lørdag 6. desember 2014
Front brake for Cutdown
I want my Cutdown to have front brake. Front brake was implemented in 28 to the IOE models from HD. This meant they made a brake anchor plate to wrap around the left leg of the rear front fork and "invented" a hub with a drum riveted to.
I have one of those anchor plates and a 28 front hub with drum, rare as hen teeth those hubs (well almost), unfortunately the drum on mine have issues with severe pitting, ouch.
From a friend I got an early thirties HD front wheel with brake, full of mud and grease, but behind all of this a nice part and it looks very much as the original 28/29 JD brake, except from!
There is always this except from!
The width is what makes the 28/29 so different, it is very narrow to get in between the fork legs of the IOE fork, the early thirties will not fit, unless.
Unless it get cut in two half`s, and shortened, hmm.
If someone need the early thirties one and have a 28/29 they better hurry up, I will swap!
I have one of those anchor plates and a 28 front hub with drum, rare as hen teeth those hubs (well almost), unfortunately the drum on mine have issues with severe pitting, ouch.
From a friend I got an early thirties HD front wheel with brake, full of mud and grease, but behind all of this a nice part and it looks very much as the original 28/29 JD brake, except from!
There is always this except from!
The width is what makes the 28/29 so different, it is very narrow to get in between the fork legs of the IOE fork, the early thirties will not fit, unless.
Unless it get cut in two half`s, and shortened, hmm.
If someone need the early thirties one and have a 28/29 they better hurry up, I will swap!
onsdag 3. desember 2014
"Halvtopp" gathering, and some beer!
Erik (Pan/WL), Rune (Pan/halvtopp) and Odd (he is the smart one as he have no old HD, or he is the bored one with no technical challenges, for you to choose).
Runes J 1927, now with DLX 45 from Sweden.
Having installed the DLX, time for refreshments in the lounge area, oops, da-boss`s Scarver in the foreground.
søndag 30. november 2014
More Cutdown progress
Made this little table on wheels to be able to work around the chassis during the winter when working.
Spent an afternoon with the foot board rods, they needed to be heated to get back to straight, the old molested 7/16" threads had to be cut off and a hole was drilled and tapped in each end, with threads 3/8"
Finally studs with 3/8"`s and 7/16"`s where made in the lathe with four nuts to make the rods complete. Locktited the 3/8" ends in the rods with 290 to make them stay.
Just a test of how the fork will look on the bike. Forgot to make pics off all the hassle I had with modifying the lower fork rocker friction dampers to fit the fork rockers (that I had ground to straight in a previous post). Front fork is shortened by an inch, curious to see how this will act when wheel installed.
Rear view, looking good?
fredag 14. november 2014
To step or not!
Have been digging in some dark corners of my workshop today, where light have not been spread for years.
Did I do any discoveries?, indeed I did.
I found a really cool old gearbox.
A Harley gearbox, of course it was.
But this specific gearbox was in its time a big change for the Milwaukee factory.
For Harley as most manufacturers it all started with belt pulleys with slipping mechanisms allowing the rider to halt. Further on the rear wheel hub gears was tried and abandoned in 1914, finally in 1915 the gearbox was an option for the modern man, who dared.
Below are brave words from Harley`s 1915 sales brochure;
Did I do any discoveries?, indeed I did.
I found a really cool old gearbox.
A Harley gearbox, of course it was.
But this specific gearbox was in its time a big change for the Milwaukee factory.
For Harley as most manufacturers it all started with belt pulleys with slipping mechanisms allowing the rider to halt. Further on the rear wheel hub gears was tried and abandoned in 1914, finally in 1915 the gearbox was an option for the modern man, who dared.
Below are brave words from Harley`s 1915 sales brochure;
** The
Three-Speed **
The
three-speed gear for the 1915 Harley-Davidson is a ‘’regular automobile
fellow.” Outwardly not conspicuous, its “bones” are large and husky. It’s the
big Harley-Davidson feature for 1915. The illustrations in this issue show that
in the three-speed model the free-wheel feature, which with the two-speed is at
the rear hub, is now at the countershaft, integral with the three-speed gear.
The change only slightly alters the line design, which remains distinctly that
of the Silent Gray Fellow.
** Eight
Thousand Miles Without Wear **
The gears
are claimed to be noiseless and can be banged back and forth without injury.
They are eight pitch and have a half-inch face-as big as gears used in many
automobiles. The distance between centers is short. The spline shaft and jack
shaft are so close together that there is no play. The rigidity of the gear box
is such that some of the machines in the engineering department have been run
8000 miles without any indication of wear or play in any part of the gear.
** A Case of
Three-in-One **
The
step-starter, the clutch and the three-speed are mounted together on a drop
forging which is part of the frame. The front chain can be adjusted by simply
sliding this unit on the frame. It can be locked instantly and the adjustment
is such that the transmission is always in line. The rear chain is adjusted in
the usual way.
An
illustration of the top of the gear box shows the locking mechanism, by which
it is made impossible for the gears to be shifted without releasing the clutch,
thus doing away with any chance of stripping gears through carelessness.
** Value of
the Intermediate **
For side
car purposes the three-speed is ideal. With the standard gear of 3.89, used on
the twins, the intermediate gear of 1 ½ gives a ratio of 5.83. In traffic or
rough going, the motor can be run on the intermediate indefinitely- a relief
from racing the motor on the low. The low gear, with its Increase of 2 ¼ gives
ratio of 8.75, which ought to pull both the driver and his side car passenger
through almost anything.
To
accommodate this increased power, the chains and sprockets are larger. Both are
1/8-inch wider and the three-speed model has a 16-tooth engine sprocket. This
it is believed, will more than double the life of the transmission.
It is
claimed that, in the low, the new model will climb a 45% grade with side car
and passenger, and that it has taken a 60% grade without side car, “without a
murmur.” The touring radius of the three-speed twin is claimed to be double
that of a two-speed machine. As for care, -no adjustments; a little oil now and
than, that’s all.
The gearbox from the dark corner:
Obviously some owner of this great 1915 Harley at some time in history was ashamed of the pedals causing the motorbike having a bicycle appearance. No problem though, every farmer boy have a hacksaw and his neighbor welding gear, voila pedals became a single pedal starter as the 1916 models and on had.
tirsdag 4. november 2014
Aussie 61" OHV sidecar racer
Another cool photo from a 1939 Enthusiast magazine.
Australian Jack Conquest gives his 61OHV a good beating during the Australian sidecar TT, a race Jack and his "spry" "monkey" won.
" SAY, these 1939 HARLEY-DAVIDSONS are beauties! - The best ever !"
OK, i admit to have wished for a Knucklehead, wished and wished, but most except a few that have come up for sale here have been, ehh not so much Knuckle other than the heads.
Mostly a mix of this and that and loads of repop, which would be OK if they where cheap and I wanted to build something else than a original looking ride.
Neither are they cheap nor did I want to build something unoriginal looking, and those projects I know of - of course they are not for sale as their owners have a plan.
Not that I should complain, I have my Bessie and her 45" siblings, but you know the feeling, the itch, the need, I WANT A KNUCKLEHEAD.
Sometimes it is all about fate, this time fate played nice to me and I was contacted by a gentleman in Oslo offering me to buy his family heirloom, a 1939 Knucklehead.
And what a bike, sold new here in Norway by Sørensen & Balchen back in 39, hidden in Sweden during the WWII to be re-registered in 1946, and the bike still have its original 1946 plates on.
Original paint in export green, a choice only available for Europe.
Lets say back in 1938 you got your latest issue of The Enthusiast that you had been waiting for, here is what you would would learn about the 1939 Harley Davidson 61" models:
Mostly a mix of this and that and loads of repop, which would be OK if they where cheap and I wanted to build something else than a original looking ride.
Neither are they cheap nor did I want to build something unoriginal looking, and those projects I know of - of course they are not for sale as their owners have a plan.
Not that I should complain, I have my Bessie and her 45" siblings, but you know the feeling, the itch, the need, I WANT A KNUCKLEHEAD.
Sometimes it is all about fate, this time fate played nice to me and I was contacted by a gentleman in Oslo offering me to buy his family heirloom, a 1939 Knucklehead.
And what a bike, sold new here in Norway by Sørensen & Balchen back in 39, hidden in Sweden during the WWII to be re-registered in 1946, and the bike still have its original 1946 plates on.
Original paint in export green, a choice only available for Europe.
Lets say back in 1938 you got your latest issue of The Enthusiast that you had been waiting for, here is what you would would learn about the 1939 Harley Davidson 61" models:
Front page of The Enthusiast September 1938, advertising the new 39 models!
Check out all these new improvements for 1939!
Re-designed instrument panel, described as eye-appealing and first year for the Beehive tail light!
The self-aligning upper and lower head cones, new for 39!
Assures smooth and easy handling for the entire life of the motorcycle.
The new and classy saddle made of two-tone russet rhino-grain horsehide leather!
The 1939 61" OHV!
"The motorcycle every rider wants to own some day"
"SPEED-ENDURANCE-STAMINA"
Of course do I want to be as fast as Joe Petrali running at an average SPEED of 136,183mph at Daytona beach in 1937.
Of course do I want to have the possibility of going longe ENDURANCE runs as Ted Kennedy when he won the Jack Pine Endurance run in 1938.
And who would not want Fred Horn`s STAMINA, he did incredible 1825,2 miles in 24 hours at Muroc dry lake in 1937.
All of this was made possible due to their choice of motorcycle, the Harley Davidson 61" OHV model.
A few pictures of my 1939 61" OHV:
A final quote from Harley Davidson;
"You, too, will some day want to own a 61" OHV if not already so fortunate".
Abonner på:
Innlegg (Atom)